Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround
Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
This great article in the next paragraphs on the subject of Tools You Need to Install a New Bathtub is extremely attention-grabbing. Don't miss out on it.
Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is readily accessible, the project can move quickly; if you have to open a wall to remove the old tub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Make certain you have qualified yourself for the job and fit trying it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This short article will help you mount a brand-new tub in your bathroom if you have actually currently gotten a new bathtub as well as don't require to alter the plan of your previous water supply pipelines.
Your devices as well as material list must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome due to the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipes have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the tap in place with the maker given backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and also tighten them if needed. Fill up the tub and additionally examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait till the bath tub has been used at the very least when as this will settle it right into its final position.
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the bath tub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to problems with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that page on How to Install a Bathtub when surfing the web. Sharing is good. Who knows, you may be doing someone a favor. Thanks so much for your time spent reading it.
Book 24/7
Report this page